Re: The distributor will install a new battery even in the coil for $50
So you're saying its best to send the detector in every time the battery runs down. So do you not hunt during that time or do you buy at least 2 so you're never without a detector. Just the problems...
View ArticleSo being without the detector for a week every 5 years or so, here in the...
I feel the Deus is very reliable and virtually problem free compared to many other detectors out there that need to be shipped back to fix problems that shouldn't be there at all and that is time...
View ArticleRe: New update
Quotesprchng Quotecalabash digger thanks for the info, to the guy above if the deus doesnt meet your needs then what detector does?IF you want to dump your deus my buddy might just take it off your...
View ArticleX/Y Screen
I have seen a few posts on the X/Y screen but I don't recall this question being asked. Is the X/Y screen a fixed representation of the TID number and regardless what program or other settings you use...
View ArticleNotch Question
Am I reading the manual correctly when I see that the notch function encompasses 6 values? In other words, If I want to notch out 45 I have to notch between 43-47 inclusive? Or some other combination...
View ArticleRe: The distributor will install a new battery even in the coil for $50
I am not saying send the machine in to get new batteries fitted/ what I am saying is that if you watch the video of how to replace the batteries and take extra care with what you are doing the...
View ArticleRe: XP DEUS BATTERIES
Replacing the batteries in the controller is relatively easy as is the coil albeit that is slightly harder due to the fact that the battery compartment needs sealing with the special sealant,of course...
View ArticleRe: X/Y Screen
I can't answer your question technically, but I seem to remember the graphic representation of a target can be influenced by both the software selection (program settings) as well as coil size. That...
View ArticleRe: Notch Question
The way I read it u notch out the group of six (3 below and 3 above) the target value u want to reject. So actually 7 values.
View ArticleRe: Notch Question
Wow, that'a a lot of notching for a target. I could see one above and one below, but 7 numbers is too broad a range. They need to change that in some software update.
View ArticleRe: Anderson Carbon Straight Shaft Question
Contact Anderson. It could be that you have a klinker. It happens sometimes in the manufacturing process and gets missed by QC. For what they cost, they should make it right for you.
View ArticleRe: Notch Question
Notch doesn't affect the vdi just the tones up to the depth the vdi quits showing. Notch is an interesting feature to work with. There are lots of posts about it. I think squirrel1 has the most...
View ArticleRe: Deus finds from a Roman site in the UK
I've done this same thing here in Vancouver, BC. I've even lowered my sensitivity as far as 75. Going back over nail/iron infested places I hit before with the HOT program and I've pulled silver coins...
View ArticleRe: Notch Question
Thanks. Like all new machines (or new to the user), there are going to be peculiarities. That's the learning curve. Reading these forums and getting pointers is a good way to shorten that learning...
View ArticleRe: Notch Question
Quotehrefab Am I reading the manual correctly when I see that the notch function encompasses 6 values? In other words, If I want to notch out 45 I have to notch between 43-47 inclusive? Or some other...
View ArticleRe: Notch Question
Page 40 deals with multi notches where a rejectible target needs a wider window, it does not deviate from the standard six point window. You may lessen the window, but will have little success unless...
View ArticleRe: Notch Question
Clearly you have your own understanding of how the notch/notches feature works,,,,onward through the fog:smile:
View ArticleRe: Notch Question
Quotesprchng Clearly you have your own understanding of how the notch/notches feature works,,,,onward through the fog:smile: Rather than a snarky comment, perhaps you could illuminate the discussion...
View Article